Products - Steel Pipes - Rectangular Tube
Rectangular Tube
Rectangular Tube
Rectangular Tube
Rectangular Tube

Rectangular Tube

Rectangular Tube

Rectangular Tube

Rectangular Tube

  • Description
  • Process
  • Equipment
  • Dimension
  • Inquiry

Rectangular Tubes __________for any details, email to us: info@great-pipe.com

Rectangular hollow sections are not as common as UCs and UBs. This is down to the fact that it is much more difficult to bolts it to other beams or to bolt other members to it. RHSs are described by their depth, width and wall thickness. An example is a 200 x 100 x 8 RHS, which is 200 mm deep, 100 mm wide and the wall is 8 mm thick. Hot rolled RHSs are made at the mill as one piece, whereas cold formed RHSs are made of a flat sheet rolled at right angles and welded. It is therefore easy to note the difference, as the cold rolled RHSs have a weld all along its length.


Standard
ASTM A500, EN 10210, EN 10219, JIS G3466, BS 1387, BS 6323 PART5
Grades
A500, S185, S235, S235JR, S235 G2H, S275, S275JR, S355JRH, S355J2H, St37, ST52
Out diameter
10*20mm - 600*400mm
Wall thickness
0.5mm - 20mm


Surface Conditions                                          Special Features

Hot Rolled                                                                Hard to find sizes

Hot Rolled Pickled and Oiled                              Mitre cutting
Cold Rolled                                                              High strength steel on request
KleenKote                                                                Mult lengths


Standard Corner Radius(Mechanical Sizes:)

Diameter (inch) Wall Thickness (inch) Radius Tolerance (inch)
1/2 to 1 1/2
0.028
1/32 to 1/16
1/2 to 2 1/2
0.035
1/32 to 1/16
1/2 to 4
0.049
3/64 to 5/64
1/2 to 4 1/8
0.065
1/16 to 7/64
3/4 to 4 1/8
0.083
5/64 to 1/8
over 4 1/8 to 6
0.095
3/16 to 5/16
1 to 4 1/8
0.095
3/32 to 5/32
over 4 1/8 to 6
0.109
3/16 to 5/16
1 1/4 to 4
0.109
1/8 to 13/64
over 4 to 6
0.120
3/16 to 5/16
1 1/4 to 4
0.120
3/16 to 5/16
over 4 to 6
0.134
7/32 to 7/16
2 to 4
0.148
3/16 to 5/16
over 4 to 8
0.148
7/32 to 7/16
2 to 8
0.165
1/4 to 1/2
2 to 8
0.180
1/4 to 1/2
2 1/2 to 4
0.203
5/16 to 9/16
over 4 to 8
0.203
5/16 to 9/16
2 1/2 to 8
0.220
3/8 to 5/8

Standard Corner Radius(Structural Sizes:)

Max. 3 x Nominal Wall Thickness

Mechanical Sizes
Structural Sizes
Largest Nominal Outside Dimension
Outside Tolerance at all Sides at Corners
Largest Nominal Outside Dimension
Outside Tolerance at all Sides at Corners
3/16 to 5/8
± 0.004
2 1/2 and under
± 0.020
over 5/8 to 1 1/8
± 0.005
over 2 1/2 to 3 1/2
± 0.020
over 1 1/8 to 1 1/2
± 0.006
over 3 1/2 to 5 1/2
± 0.030
over 1 1/2 to 2
± 0.008
over 5 1/2
± 1%
over 2 to 3
± 0.010


over 3 to 4
± 0.020


over 4 to 6
± 0.020


over 6 to 8
± 0.025



Straightness
Mechanical Sizes: Max. 1/16" in 3 feet
Structural Sizes: Max. 1/8" x Number of feet of total length divided by 5


Wall Thickness
Mechanical & Structural Sizes: ± 10% of Nominal Wall Thickness

Squareness of Sides
Mechanical Sizes: Max: ± b = c x 0.006"
                        b = Tolerance for out-of-square
                        c = Largest external dimension across flats
Structural Sizes: Adjacent sides may deviate from 90 ° by ± 2 °


Maximum Twist (Mechanical & Structural Sizes)

Largest Dimension, inches
Max. Twist*, inches
over 1/2 to 1 1/2
0.050
over 1 1/2 to 2 1/2
0.062
over 2 1/2 to 4
0.075
over 4 to 6
0.087
over 4 to 8
0.100

Convexity & Concavity(Mechanical & Structural Sizes)

Largest Nominal O.D., Inches 
Tolerance ± Inches
2 1/2 and under
± 0.010
over 2 1/2 to 4
± 0.015
over 4 to 8
± 0.025

Structural Tubing A 500 Requirements

Grades Chemical
Physical
C Max. %
Mn Max. % P Max. % S Max. % Cu Max. % Tensile strength, min. psi
Yield strength, min. psi
Elongation in 2 in.
B
0.26
/ 0.04
0.05 0.20 58,000
46,000
23
C
0.23
1.35
0.04
0.05 0.20 62,000
50,000
21






If you have any inquiries and problems, please contact Hunan Great Steel Pipe Co.,ltd at any time. Thanks in advance. Welcome! Email:info@great-pipe.com